MCU: различия между версиями

Материал из fidoman.ru
 
(не показано 19 промежуточных версий этого же участника)
Строка 6: Строка 6:
  
 
Lightweight C compilers http://fun4diy.com/
 
Lightweight C compilers http://fun4diy.com/
 +
 +
https://sdcc.sourceforge.net/
  
 
== STM8 ==
 
== STM8 ==
  
 
compilers comparation http://www.colecovision.eu/stm8/compilers.shtml
 
compilers comparation http://www.colecovision.eu/stm8/compilers.shtml
 +
 +
samples https://www.hodges.org/rh/stm8/
  
 
=== startup ===
 
=== startup ===
Строка 26: Строка 30:
 
=== AWU ===
 
=== AWU ===
  
−
* on int disable AWU (or new int will generated instantly)
+
* on int disable AWU (or new int will be generated instantly)
 
* before re-enable re-load counter
 
* before re-enable re-load counter
 +
 +
=== UART ===
 +
 +
- word length: UART_CR1.M
 +
- stop bits: UART_CR3
 +
- baud rate: UART_BRR2 then UART_BRR1
 +
- en transmitter: UART_CR2.TEN
 +
- send data: UART_DR and wait until TC goes 1
 +
 +
UART_DR:
 +
  write goes to TDR
 +
  read goes from RDR
 +
 +
TXE: set at end of transmission (and if TIEN then int is generated) - can send more
 +
  wait for TXE before write DR
 +
 +
TC: transmission complete (and if TCIEN then int is generated) - may disable transmitter
 +
 +
SBK bit: send '''break''' character (do not set again before prv '''break''' is sent)
 +
 +
UART_CR1.R8: MSB for received 9-bit words
 +
 +
NF: set when start bit has spurious '1's
 +
 +
- en receiver: UART_CR2.REN
 +
 +
clear REN to abort receive immediately
 +
 +
RXNE: set when data moved to RDR (and intr if RIEN set)
 +
 +
if char is received without RXNE reset then overrun error raised
 +
 +
break char: received as framing error
 +
 +
idle char: intr if ILIEN set
 +
 +
- UART_CR1.PCEN : one bit of total length will be used for parity
 +
- UART_CR1.PS : even/odd parity
 +
 +
- UART_CR1.RWU: mute mode. WAKE = 0: until idle, WAKE = 1: listen for address (MSB=1 as mark of address - 4 bits LSB)
 +
- UART_CR4.ADD: own address
 +
- only first byte after idle considered as possibly containing address mark? not clear.
 +
 +
=== jobs ===
 +
 +
MAYHALT - semaphore, must be incremented on start of each no-halt process e.g. UART TX
 +
syssleep func:
 +
  check for mayhalt
 +
  if zero halt
 +
  if not wfi
 +
  loop if no jobs else get toppest by pri and start
 +
 +
sysjobs:
 +
  populated with int handlers, address of jobs to run (with associated data ptr)
 +
 +
sysqueues:
 +
  if smth is put on it, associated job is created by system
 +
  queue record:
 +
    what to do, data, completion action
 +
 +
for example, if program puts report on send queue and queue is full, program must be suspended
 +
or something in queue must be deleted
 +
 +
alternatively, program can put something on queue, asking to suspend self and to be resumed on completion
 +
 +
=== applications ===
 +
 +
* receive byte from serial and set ON/OFF switches
 +
* receive byte from serial and set voltage
 +
* one MCU reads ON/OFF or voltage and send to another to set same ON/OFF or voltage value

Текущая версия на 16:10, 21 февраля 2023

cam

ESP32-CAM OV2460

links

Lightweight C compilers http://fun4diy.com/

https://sdcc.sourceforge.net/

STM8

compilers comparation http://www.colecovision.eu/stm8/compilers.shtml

samples https://www.hodges.org/rh/stm8/

startup

  1. Power requirements: 3.3-5V
  2. Reset circuit (100nF cap)
  3. Select clock source (ext.crystal/HSI)
  4. Choose halt modes for
    1. flash
    2. HSI, HSE
  5. use timer or AWU for wake-up if no ext.ints
  6. calibrate LSI osc.
  7. configure GPIO
  8. use watchdog

AWU

  • on int disable AWU (or new int will be generated instantly)
  • before re-enable re-load counter

UART

- word length: UART_CR1.M
- stop bits: UART_CR3
- baud rate: UART_BRR2 then UART_BRR1
- en transmitter: UART_CR2.TEN
- send data: UART_DR and wait until TC goes 1

UART_DR: 

 write goes to TDR
 read goes from RDR

TXE: set at end of transmission (and if TIEN then int is generated) - can send more 

 wait for TXE before write DR

TC: transmission complete (and if TCIEN then int is generated) - may disable transmitter

SBK bit: send break character (do not set again before prv break is sent)

UART_CR1.R8: MSB for received 9-bit words

NF: set when start bit has spurious '1's 

- en receiver: UART_CR2.REN

clear REN to abort receive immediately

RXNE: set when data moved to RDR (and intr if RIEN set)

if char is received without RXNE reset then overrun error raised

break char: received as framing error

idle char: intr if ILIEN set 

- UART_CR1.PCEN : one bit of total length will be used for parity
- UART_CR1.PS : even/odd parity

- UART_CR1.RWU: mute mode. WAKE = 0: until idle, WAKE = 1: listen for address (MSB=1 as mark of address - 4 bits LSB)
- UART_CR4.ADD: own address
- only first byte after idle considered as possibly containing address mark? not clear.

jobs

MAYHALT - semaphore, must be incremented on start of each no-halt process e.g. UART TX syssleep func: 

 check for mayhalt
 if zero halt
 if not wfi
 loop if no jobs else get toppest by pri and start

sysjobs: 

 populated with int handlers, address of jobs to run (with associated data ptr)

sysqueues: 

 if smth is put on it, associated job is created by system
 queue record:
   what to do, data, completion action

for example, if program puts report on send queue and queue is full, program must be suspended or something in queue must be deleted

alternatively, program can put something on queue, asking to suspend self and to be resumed on completion

applications

* receive byte from serial and set ON/OFF switches
* receive byte from serial and set voltage
* one MCU reads ON/OFF or voltage and send to another to set same ON/OFF or voltage value
Источник — https://fidoman.ru/w/index.php?title=MCU&oldid=91